Owatrol

RUSTOL – Rust Protector – OWATROL

44.95 $X

RUSTOL-OWATROL NEUTRALIZE AND DEEPLY PROTECT

RUSTOL-OWATROL is a versatile rust protector and highly penetrating oil that can be used alone or added to paint. In addition to neutralizing and protecting surfaces treated with OWATROL SPIRITS, RUSTOL-OWATROL adds semi-gloss appearance to the finish of your projects.

Used alone: ​​It offers a resistant and flexible finish while removing excess moisture and air which allows it to stop rust. It fills the porous and dry wood to stop the peeling of the paint.

Added to all oil or alkyd coatings: It increases the working time, it improves the flow capacity, it offers better adhesion and, unlike damaging thinners, it maintains the inherent quality of the paint without affecting its appearance or drying time.

  • Colourless rust inhibitors with great wetting power;
  • Removes air and humidity from the support;
  • Apply directly on rust;
  • Forms a protective, insulating and flexible film;
  • Hanging base for all types of supports;
  • Easy to use, with no sanding needed;
  • Additive for paints, stains, glycerophthalic varnishes and alkyd urethane;
  • Make painting anti-rust while facilitating its application and improves its grip;
  • Gives greater flexibility of the film;
  • Decorative: preserves the rusty appearance of the supports while protecting them.

DESTINATION:

  • Indoor and outdoor;
  • Ferrous and non-ferrous metals, plastics, glass, wood, etc.;
  • An undercoat before paints and varnishes;
  • Compatible with all varnishes, paints, lacquers and stains with fatty binder (alkyd) drying in the air, anticorrosion paints, oil paints, glycerophthalic paints, one component urethans, paints based on petroleum asphalts, fatty coatings, etc.
  • Do not add to quick-dry “body type” paints or chlorinated rubber or two-component paints.

PREPARATION:

AS AN ANTI-RUST OR A BASE TO ADHERE ON A DIFFICULT SUBSTRATE:

  • Surfaces must be clean, dry, and free from oil, grease, and other surface contaminants;
  • Remove all scales of rust and old paint. Soften the sharp edges;
  • Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using hot water or steam. Let dry;
  • Severely contaminated surfaces should be cleaned with an appropriate solvent (CITRUS SOLVENT);
  • Do not remove encrusted rust;
  • Do not sand to bare metal.

AS A PAINT ADDITIVE:

  • Prepare the surface according to the instructions on the paint bucket;
  • Remove all scales of rust and old paint. Soften the sharp edges;
  • Always do a compatibility test before starting a project.

APPLICATION:

AS AN ANTI-RUST OR A BASE TO ADHERE ON A DIFFICULT SUBSTRATE:

  • New surfaces with little oxidation or mechanically stripped:
    • Clean and degrease carefully (TSP, CITRUS SOLVENT, etc.);
    • Apply a thin and uniform coat of pure RUSTOL-OWATROL®;
    • After drying, inspect the surface and make sure it is evenly protected.
  • Formerly painted and rusted surfaces:
    • Remove rust and paint flakes by wire brushing;
    • Clean and degrease carefully (TSP, CITRUS SOLVENT, etc.);
    • Apply a thin and uniform coat of RUSTOL-OWATROL®;
    • After drying, inspect the surface and make sure it is evenly protected.

AS A PAINT ADDITIVE:

  • Make a compatibility test between mixed products and the surface;
  • To make anti-rust paints: provide a mixture of 25% RUSTOL-OWATROL®/75% paint;
  • To adhere to a difficult surface: use a 50/50 RUSTOL-OWATROL®/paint mixture;
  • To facilitate the application of thick paints (instead of diluent) add 5% of RUSTOL-OWATROL® to the paint.

DRYING TIME:

  • Dry to touch: after 12 hours;
  • Complete drying: after 24 hours depending on temperature and humidity;
  • Cover: after 24–48 hours.

NUMBER OF COATS:

Varies depending on the type of application.

COVERAGE:

18 m2 / L

The coverage may vary depending on the type, texture and porosity of the surface as well as the method of application chosen.

TOOL CLEANING:

Clean all tools and equipment with CITRUS SOLVENT while they are still wet. If the product is dried, remove with a paint stripper.

NOTE: Any clothes, steel wool or material soaked in RUSTOL can ignite spontaneously if improperly disposed of. They should be saturated with water after use or laid flat to dry before discarding.

FINISH:

Transparent semi-gloss.

SIZES:

1 L

STORAGE AND LOGISTICS:

Protect from frost and high temperatures.

RUSTOL should be transferred to a smaller, airtight metal or glass container and closed after use. Minimum duration of 2 years in sealed original packaging.

Refer to the available safety data sheet (SDS) in the DOCUMENTS section and to the texts on the packaging, in accordance with current legislation.

DISPOSAL AFTER USE:

Soaked rags should not be stored or thrown directly into a trash can. Dry them flat beforehand. Dangerous. Read precautions before use.