EVO

EVOPOLY+ – Solvent-Free Polyaspartic – EVO

189.95 $399.95 $X

Solvent and VOC-Free Polyaspartic Coatings !

EVOPOLY+ is a solventfree, twocomponent polyaspartic coating, perfectly suited for all concrete and wood finishing projects, both interior and exterior: worktops, countertops, bars, pool towers, concrete porches, concrete slabs. This product can also be used for residential, institutional, industrial and commercial concrete floors. EVOPOLY+ offers superior resistance to abrasion and chemical attack than conventional epoxies. It provides a smooth, glossy finish that will not turn yellow. EVOPOLY+ can be used as a base coat as well as a topcoat. Polyaspartic coatings have a very fast drying time, allowing the entire job to be done in one day. EVOPOLY+ can be applied at cold temperatures down to 10°C.

  • Nonyellowing
  • 100% solid resins
  • Solvent and VOCfree
  • Excellent abrasion resistance
  • Interior and exterior applications
  • Two component polyaspartic system
  • Slow set time for easy application (35 minutes)
  • Superior mechanical and chemical resistance properties

PREPARATION WOOD :

  • The wood must be clean and dry.
  • Sand the surface to 120 grit. In the case of a river table, the epoxy must also be sanded.
  • We recommend sealing the wood with a solvent or waterbased varnish sealer to avoid bubbles created by gases released from the wood.

PREPARATION BARE CONCRETE :

  • The concrete must be clean, dry and free of grease, oil, paint, curing compounds or any other contaminants that may affect the adhesion of the product.
  • If applying to a new concrete surface, a cure time of at least 28 days is required before applying EVOPOLY+.
  • First, clean the surface with an alkaline concrete cleaner such as EVO CONCRETE CLEANER to remove all traces of grease and contaminants.
  • Mechanical surface preparation : Resurfacing with a mechanical concrete grinder is the best preparation. However, for most residential projects you can prepare the surface with a sanding operation. Use 2460 grit sandpaper (ideally with ceramic grit).

PREPARATION PAINTED CONCRETE :

  • All traces of paint must be removed from the surface. First, clean the surface with an alkaline concrete cleaner, such as EVO™ CONCRETE CLEANER, to remove all traces of grease and contaminants.
  • Sand the surface with a 4060 grit sandpaper (ideally with ceramic grit).
  • If the product is being applied over an epoxy system that has aged for more than 24 hours, the surface must first be sanded with a 60 grit abrasive and properly cleaned with a vacuum. This preparation is necessary to ensure adequate adhesion.
  • We recommend appropriate adhesion tests if there is any doubt about the surface preparation.

Important : If you are applying on a topcoat, you must also sand to create an anchor profile. A compatibility test should be carried out beforehand.

MIXING :

  • Before final mixing, it is recommended that parts A and B of the product be thoroughly mixed individually at low speed (300450 rpm).
  • Pay particular attention to the coloured versions of the product as the pigments may have separated from the rest of the formulation during storage. Mixing is completed when a uniform colour is achieved.
  • In a clean container, mix part A and part B with a lowspeed drill (300450 rpm). Be sure to use clean equipment to avoid contaminating the product.
  • Mix slowly and thoroughly for 3 to 5 minutes so as to avoid air bubbles in the product and scrape down the sides to the bottom of the mixing container.
  • For small projects, be sure to mix only the amount of product needed.
  • Once the product is mixed, you have 35 minutes of working time.

APPLICATION :

  • Before applying EVOPOLY+ make sure that the air and floor temperature is between 10 and 30°C and that the humidity level does not exceed 85%.
  • Pour the product directly onto the floor in parallel lines.
  • Then spread the product with a squeegee and roll with an epoxy roller in both directions, parallel and perpendicular, to even out the surface.
  • You can only spread the product with a high quality 13 mm microfiber epoxy roller. EVOPOLY+ can be applied both as a base coat (directly on the concrete) and as a topcoat.
  • We recommend applying a base coat of approximately 6 to 8 mils (thousandths of an inch) thick, followed by a topcoat of approximately 6 mils on solid colour.
  • If your surface contains flakes, complete the finish with two 4 mils coats to ensure that the flakes are fully coated.

NUMBER OF COATS :

1 to 3 depending on the project.

DRYING TIME (~22 °C) :

  • WORKING TIME : 35 minutes.
  • DRY IN DEPTH : 24 hours.
  • BETWEEN COATS : 6 to 24 hours.
  • LIGHT CIRCULATION : 7 hours.
  • FULL CURE TIME : 10 to 14 days.
  • NOTE : Working time can be reduced by up to 50% if the product is applied in very hot weather (~35 °C).

TOOL CLEANING :

Denatured alcohol or acetone.

COVERAGE :

  • 4 Mils : 105 ft2 / L
  • 6 Mils* : 66.5 ft2 / L
  • 10 Mils : 40 ft2 / L
  • 15 Mils : 26.5 ft2 / L

* : A thickness of 6 mils is approximately equivalent to a 13 mm applicator roll.

FORMATS :

  • Medium (A : 1 x 946 mL | B : 1 x 946 mL)
  • Large (A : 1 x 3,78 L | B : 1 x 3,78 L)

COLOURS :

Clear | White | Grey | Black | Tan

FINISH :

Glossy.

MAINTENANCE :

EVO Black Soap.

STORAGE :

Store containers away from UV light (in the box) and protect from freezing.

LIFETIME :

The shelf life of EVOPOLY+ is 10 to 12 months in its original container.

DISPOSAL :

Excess liquid from Parts A and B should be mixed to allow for curing and dispose in accordance with applicable provincial and federal regulations.

data grid evopolyplus en

Technical data sheet

Safety data sheet – Part A

Safety data sheet – Part B

Colours are approximate and may vary from screen to screen. True colours may vary depending on the surface to be covered.